An upper/lower split alternates two sessions: an upper-body day (chest, back, shoulders, arms) and a lower-body day (quads, hamstrings, calves). Kaltro ships both as built-in day-templates — tap one to start that session — and on four days a week each half gets trained twice. This page shows what is in each day, how much, and how hard.

Lifters often search for an “upper/lower program”; in Kaltro you run it as two day-templates you start one tap at a time. A split is just a scheduling tool — the volume and effort you accumulate over the week are what drive results.

Who this is for — and who it isn’t

  • Good fit: lifters training about four days a week — late-beginner through advanced. It is a practical middle ground: more per-muscle volume per session than full-body, less frequency demand than a six-day split.
  • Training only two or three days a week? A full-body template means nothing gets skipped that week, so it is the better fit.
  • Want higher frequency? If you can train five or six days and recover from it, a push/pull/legs split spreads the same work across more sessions.
  • Returning from a long layoff or an injury: ramp load back gradually and get clearance first (see the note at the end).

The two day-templates

Each is built into Kaltro as its own template — one tap starts that session. Set counts are working sets (warm-ups are extra and are not counted by Kaltro’s analytics). Each template prefills a single rep target per exercise; the ranges shown are Kaltro’s defaults for a hypertrophy goal (or general fitness, or no goal set), and you fill the range before the weight goes up. Set a strength or endurance goal in your profile and Kaltro uses its ranges for that goal instead.

Upper body — chest, back, shoulders, arms

  • Barbell Bench Press — 4 working sets, 8–12 reps
  • Bent Over Barbell Row — 4 working sets, 8–12 reps
  • Barbell Overhead Press — 4 working sets, 8–12 reps
  • Lat Pulldown — 3 working sets, 8–12 reps
  • Incline Dumbbell Press — 3 working sets, 8–12 reps
  • Seated Cable Row — 3 working sets, 8–12 reps
  • Dumbbell Lateral Raise — 3 working sets, 12–15 reps
  • Barbell Curl — 3 working sets, 12–15 reps
  • Cable Tricep Pushdown — 3 working sets, 12–15 reps

Lower body — quads, hamstrings, calves

  • Back Squat — 4 working sets, 8–12 reps
  • Romanian Deadlift — 4 working sets, 8–12 reps
  • Leg Press — 3 working sets, 8–12 reps
  • Hack Squat — 3 working sets, 8–12 reps
  • Leg Extension — 3 working sets, 12–15 reps
  • Lying Leg Curl — 3 working sets, 12–15 reps
  • Hip Adductor Machine — 3 working sets, 12–15 reps
  • Machine Standing Calf Raise — 4 working sets, 12–15 reps

How much: weekly volume in sets

Count training volume as hard sets per muscle per week. These are heuristics, not measured limits.

  • A rough target is 10–20 hard sets per muscle per week for most intermediate lifters chasing size. Trained twice a week, chest, shoulders and hamstrings each get 14 direct working sets and back gets 20 — inside that zone — but quads get 26, over the top of it. To bring quads to 20, drop Hack Squat from both lower days.
  • It is a range, not a threshold. No single number is optimal, and more is not always better — returns diminish as sets pile up and recovery is the real ceiling. Use these as starting points to adjust by feel and performance.
  • Add sets slowly — one at a time, and only once your recent weeks are being recovered from and progressed. The volume calculator totals a session for you.

How hard: effort, not failure

Most working sets should be genuinely hard but not maximal.

  • Aim for about RPE 7–8 — two to three reps in reserve on most working sets: hard enough to drive adaptation, with room to recover and repeat.
  • You do not need to take every set to failure. Occasional close-to-failure work is fine; doing it on everything just deepens fatigue.
  • Log RPE if you want Kaltro to use it. It is optional — the app never invents an effort score — but when you log it, the suggestion engine reads it.

How to progress: reps first, then weight

Kaltro uses double progression — earn the reps at a weight before the weight moves.

  • Fill the rep range, then add weight. When every working set reaches the top of its range at a controlled effort, add the smallest load your equipment allows and rebuild the reps.
  • No fixed +2.5 kg-every-session promise. Progress comes when the sets say so, not on a schedule. See exactly how Kaltro decides when to add weight.

When to back off: deload by trigger

A deload is a planned lighter stretch — timed by signal, not by the calendar.

  • Reduce when performance says so: Kaltro reads three signals from your log — reps sliding at the same weight, a long time away, and logged effort staying high across consecutive sessions. It does not read sleep: if a run of poor nights leaves you flat, backing off is your call. Then drop volume or load for a spell and rebuild.
  • Not “every fourth week” by default. Kaltro calls deloads from your logged trends, never a fixed date — see when Kaltro calls a deload.

The spreadsheet (and a CSV-import demo)

Two separate things — keep them straight.

  • To run the split, use the built-in templates. They are already in Kaltro; tap Upper or Lower to start that session. You do not import anything to get them.
  • The CSV is a plain spreadsheet of the movements above, and a way to try Kaltro’s generic CSV import, which turns each row into a history entry you then fill in. It does not install a reusable template — the built-in ones already do that.
  • Weight and rep cells are intentionally blank so you enter your own loads in your own units. The file carries the structure; you bring the numbers.

Download the upper/lower spreadsheet (CSV)

This is general education, not medical advice. If a movement causes pain, or you are returning from injury or a long layoff, check with a qualified professional before loading it.

Run it with the reasoning shown

Start an upper or lower template in Kaltro, log your sets, and the app suggests the next step — and shows you why, from the sets you logged, on your device.

Other splits: push/pull/legs and full-body three times a week. Terms in plain English: progressive overload and working set. To train from these in the app, or write your own, see templates and workouts in Kaltro.